Engineering Cutting Tools

Approx. Rs 521 / PieceGet Latest Price

Approx. Rs 1,000 / PieceGet Latest Price

Boring bars are used for INTERNAL MACHINING on CNC or manual lathes. A boring bar is used to increase the diameter or finish machine a pre-existing hole.

We have a full range of boring bars including: double clamp, steel shank, carbide shank, through coolant, lever lock and screw clamp for ALL ISO turning inserts.

The most popular boring bar is 95 degree SCLCR style tool which is screw clamping and available in steel or carbide shank.

For negative turning inserts, we always recommend using DOUBLE CLAMP boring bars instead of lever lock. Double clamps offer the most secure clamping, preventing insert lift and eliminating vibration. Double clamp turning tools can increase insert tool life by as much as 40% whilst improving surface finish. For deeper boring applications carbide shank boring bars can be used for boring up to 5 times diameter deep (5XD). Through coolant boring bars can increase insert tool life and help clear swarf better.

Approx. Rs 553 / PieceGet Latest Price

Approx. Rs 253 / PieceGet Latest Price

Approx. Rs 72 / PieceGet Latest Price

• Ideal for mass production drilling
• Ground from solid micro-grain carbide
• Suitable for cast steel, cast iron, chilled cast iron, malleable cast iron, nonferrous heavy metal, nonferrous light metal, and abrasive plastic
• Self-centering
• Good chip removal

Approx. Rs 72 / PieceGet Latest Price

Quality, high volume thread production, are the result of special tool geometry engineered to optimize the benefits of premium steel and specialized coating like TiN, TiCN, TiALN.

Are precision ground on CNC thread grinders for consistent and close thread tolerances.

• Hand Taps
• Machine Taps "A", "C" and "D" as per ISO, DIN and ANSI Standards.
• Spiral Pointed Tap.
• Spiral Flute Taps.
• Roll Taps (Fluteless).
• THREAD SPECIFICATIONS Metric Coarse, Matric Fine, UNC, UNF, BSW, BSF, NTP, NPTF, NPS, NPSF, BSP, BA etc.
• TOLERANCE Metric in 6H & 6G, UNC/ UNF in 2B & 3B.
• Straight Flute hand taps are used for hand tapping and machine tapping in through holes or blind holes in a wide variety of materials.
• Spiral Flute taps lift the chips out of the hole in blind hole tapping, eliminating chip disposal problems, damaged threads and broken taps. They will also bridge interruptions in the tapped hole.
• Slow Spiral taps have stronger cutting edge (less susceptible to chipping) than Fast Spiral taps and are recommended for general purpose applications.
• Titanium Nitride (TiN) Coating results in an extremely hard surface with high lubricity for increased tool life, improved thread quality, reduced torque and increased tapping speeds for greater productivity.
• 
  BSW
  BSF
  UNF
  UNC
  UNEF
  UN
  Whit Worth Fine
  BSP
  Metric Coarse and Fine
  ME
  BSC
  BSCON
  NPT
  BSPT
  PG
  ACME

Approx. Rs 1,053 / PieceGet Latest Price

The Z-Carb-AP Patented Variable Rake Carbide End Mill offers performance so advanced, it goes way beyond typical “high performance” end mills. Superior chatter suppression through an unequal helix design and patented variable rake angle. Achieve incredible accuracy and improved shearing capabilities with enhanced corner geometry and tight-tolerance corner radius.

V-Carb 5-flute solid carbide end mills for finishing and semi-finishing produce an exceptional finish while tackling heavy milling tasks, including roughing and slotting. V-Carb can be run at higher production rates, is coated, and is available in stub, regular, and long flute lengths for any finishing application.

S-Carb solid carbide end mills for aluminum, non-ferrous, and non-metallic materials feature an engineered flute design that provides effective chip removal at high feed rates and lower cutting forces. Unique symmetrical end gashing improves balance and finish, and a circular land increases control and reduces chatter. Available for exceptional performance in aluminum and magnesium alloys.

Approx. Rs 1,753 / PieceGet Latest Price

Approx. Rs 110 / PieceGet Latest Price

Double ended tool for centreing prior to drilling or for producing a countersink from, for lathe centre location.
Suitable for both hand and machine use.

Approx. Rs 53 / PieceGet Latest Price

1. Suitable Materials:

§ PCB, normal FR-4, CEM-3 boards, environmental protection board, SMT, CNC, molds, plastic, stainless steel and precision hardware processing;

§ Circuit board, carbon fiber, composite board, and so on.

2. Features:

(1) Select high-quality ultrafine grain tungsten steel bar, precision machining by high accurate equipment;

(2) With good milling and cutting performance, ensuring high efficiency;

(3) High hardness, wear resistance, and intensity; anti-bending;

(4) To removing chips, with big space and small resistance;

Smooth chip removal, less heating value, to reduce pollution;

(5) Sharp cutting edge, reduce cutting force, lower breaking rate and improve the quality of hole wall;

(6) Symmetrical cutting blade, help to high effective cutting, avoiding drilling offset.

Approx. Rs 52 / PieceGet Latest Price

Approx. Rs 172 / PieceGet Latest Price

1. SQUARE GROUND TOOL BITS
2. ROUND TOOL BITS
3. RECTANGULAR GROUND TOOL BITS
4. Parting Tool CUT – OFF BLADES

Approx. Rs 110 / PieceGet Latest Price

Approx. Rs 120 / PieceGet Latest Price

To furnish the diverse requirements of our clients in the best possible manner we are involved in offering an extensive range of File attached for different sizes

Approx. Rs 421 / PieceGet Latest Price

Approx. Rs 253 / PieceGet Latest Price

we specialize in a comprehensive range of high speed steel tool bits in a variety of shapes, sizes material. Excellent quality tool bits, recommended for cuts at higher speed, most suitable for heavy work on difficult materials and ideal, general purpose tool bit for machine shops. The term tool bit generally refers to a non-rotary cutting tool used in metal lathes, shapers, and planers. Such cutters are also often referred to by the set-phrase name of single-point cutting tool. The cutting edge is ground to suit a particular machining operation and may be resharpened or reshaped as needed. The ground tool bit is held rigidly by a tool holder while it is cutting. The rectangular flat high speed steel (hss) toolbit that we offer, are manufactured using superior grade steel. The rectangular flat tool bits are extensively demanded because of its durability and perfect finishing. These are available in m2, m35, m42, t42, t1 and other special hss and carbide grades.

the overall shape of the lathe tool bits can be rounded, squared, or another shape as long as the proper angles are included. Tool bits are identified by the function they perform, such as turning or facing. They can also be identified as roughing tools or finishing tools. Generally, a roughing tool has a radius ground onto the nose of the tool bit that is smaller than the radius for a finishing or general-purpose tool bit. Experienced machinists have found the following shapes to be useful for different lathe operations.

a right-hand turning tool bit is shaped to be fed from right to left. The cutting edge is on the left side of the tool bit and the face slopes down away from the cutting edge. The left side and end of the tool bit are ground with sufficient clearance to permit the cutting edge to bear upon the workpiece without the heel rubbing on the work. The right-hand turning tool bit is ideal for taking light roughing cuts as well as general all-around machining.

a left-hand turning tool bit is the opposite of the right-hand turning tool bit, designed to cut when fed from left to right. This tool bit is used mainly for machining close in to a right shoulder.

the round-nose turning tool bit is very versatile and can be used to turn in either direction for roughing and finishing cuts. No side rake angle is ground into the top face when used to cut in either direction, but a small back rake angle may be needed for chip removal. The nose radius is usually ground in the shape of a half-circle with a diameter of about 1/32 inch.

the right-hand facing tool bit is intended for facing on right-hand side shoulders and the right end of a workpiece. The cutting edge is on the left-hand side of the bit, and the nose is ground very sharp for machining into a square corner. The direction of feed for this tool bit should be away from the center axis of the work, not going into the center axis.

a left-hand facing tool bit is the opposite of the right-hand facing tool bit and is intend to machine and face the left sides of shoulders.

high speed steel tool bits are manufactured from the finest quality cobalt, molybdenum tungsten bearing grades of high speed steel. Widely used for machining and variety of ferrous and nonferrous metals. Sophisticated heat treatment provides more life between two regrinds.

1. Square ground tool bits

2. Round tool bits

3. Rectangular ground tool bits

4. Parting tool cut off blades

Approx. Rs 1,000 / PieceGet Latest Price

Approx. Rs 253 / PieceGet Latest Price

Approx. Rs 553 / PieceGet Latest Price

Reamer is a type of rotary cutting tool used in metalworking. Precision reamers are designed to enlarge the size of a previously formed hole by a small amount but with a high degree of accuracy to leave smooth sides. There are also non-precision reamers which are used for more basic enlargement of holes or for removing burrs. The process of enlarging the hole is called reaming. There are many different types of reamer and they may be designed for use as a hand tool or in a machine tool, such as a milling machine or drill press.

1.Hand Reamer

2.Machine Reamers

3.Pin Reamers;

4.Tapered Reamers;

Approx. Rs 110 / PieceGet Latest Price

Adjustable Round Split dies use a set screw for adjustment of the thread size for precision threading aplications.
High Speed Steel dies recommended for longer tool life.
The quality of our dies cuts excellent threads (even into stainless steel) and provides an acceptable alternative to HSS They are far superior to alternative carbon steel dies.
These dies offer significant savings to the model engineer over HSS while offering no sacrifice in quality and performance.

Approx. Rs 253 / PieceGet Latest Price

Rotary Burrs also called debur is a grinding tools used by Pneumatic or electric Die Grinder.

Usages:

For milling, deburring, break edges, trim process welding seams, and surface processing.

Applications: For High-alloy steels, non-rusting steels,acid-resistant steels,heat-resistant steels,diecasis,roughing

steels stainless steel, aluminium, light alloys, non-ferrous metals brass, copper, zinc, diecasts and plastics.

Manufacturing Features:

lCNC FULLY GROUDING, Tolerance controlled at .005-.001mm

ldifferent cut are available (Standard Single,Fine Single, Coarse cutter, Chip Breaker, Double-Cut(Cross)

Coarse Double-cut,Fine Double-Cut, Diamond Cut, Non-Ferrous-Aluminium Cut).

lAll the burrs are available also with High Speed Steel HSS

Approx. Rs 5,221 / PieceGet Latest Price

Tooling indexable insert cutting tools for the metalworking industry. We offer expert design and build capabilities for custom tooling and an extensive line of catalog standards for Turning, milling, slotting and hole making. Boring Bars, Counterbores, Countersinks,Drills, Reamers, End Mills, Milling Cutters, Slotting Cutters & Tool Holders.

Approx. Rs 110 / PieceGet Latest Price

Approx. Rs 2,153 / PieceGet Latest Price

Approx. Rs 2,153 / PieceGet Latest Price

Approx. Rs 2,100 / PieceGet Latest Price

Approx. Rs 221 / PieceGet Latest Price

Additional Information:

• Item Code: Parallel-TaperShank

Approx. Rs 2,153 / PieceGet Latest Price

We have a complete range of CNC toolings, including ER Collets, Side Lock Adoptors, Keyless Drill Chucks, Wrenches, Revolving Centres etc.
We have a large selection of Metric and Inches High Precision CNC Spring Collets in ER and RDO Styles, Extensions, Adapters/Holders and Retaining Studs for CNC Machines. All spring collets are inspected for quality & 100% accuracy.

The high precision spring collets allow to reduce the vibrations on the tools and motors, assure better results and prolong the life of the tools and electrospindles. Our high precision spring collets used on their industrial toolholders result in the very best tool performance. 

Approx. Rs 221 / PieceGet Latest Price

Morse taper shank drill bits are designed to be mounted into a lathe tailstock or directly into a spindle tool. Primarily used in lathes and milling machines, the morse taper shank drill has excellent accuracy and can withstand greater force on the shank.

This unique range of Morse Taper Shank Drill Bits are designed to cater for all engineers drilling needs and offer a solution to all drilling problems where other drills cannot cope or stand up to modern manufacturing speeds and methods. The Morse Taper Shank series drills come in HSS and HSS-Co variants, in MT1, MT2, MT3, MT4, MT5 and MT6 tapers.

A price sensitive range of drill bits, an unsurpassed combination of price and quality. These drills are mainly roll forged, and provide the user with a drill bit that competes on price with all value brands, but doesn’t compromise the quality of the holes being drilled, and the amount of drills required.
Our range of HSS drills bits that offer benchmark quality, precision ground drill bits that maintain precise diameters, thus leaving precision tolerance in drilled holes. Not only are our HSS drills precise, they also last longer under production conditions, excavate swarf quicker and feature a ‘split point’ or ‘self centering’ tip.

Taper Shank Drills are used for drilling in:

§ Alloyed and Non alloyed Steel

§ Soft Stainless Steel

§ Soft Cast Iron

§ Aluminium

§ Copper

§ Brass and Bronze

§ Plastics

Approx. Rs 2,100 / PieceGet Latest Price

Approx. Rs 2,153 / PieceGet Latest Price

Angle Cutters (Single Angle Cutters and Double or Equal Angle Cutters) are milling cutters with their cutting face angled with respect to the axis of rotation. There are two types of angle cutters that we manufacture and stock which are the Single Angle Cutters and Double (Equal) Angle Cutters.

Single Angle Cutters are those which have teeth on the conical or angular face of the cutter and also on the large flat side. Double or Equal Angle Cutterd have V- shaped (equal angled) teeth with both conical surfaces at an angle to their end faces. Single Angle and Double (Equal) Angle Cutters are cutting tools commonly used for cutting various kinds of metals.

Single Angle Cutter Used for milling Dovetails, Serrations, Angular Slots or Chamfers. Note: A 1mm flat may be added to maintain integrity of the cutting point on certain angle and diameter combinations.

Double / Equal Angle Cutter Used for milling V-shaped slotts, serrations and chamfers. Note: A 1mm flat may be added to maintain integrity of the cutting point on certain angle and diameter combinations.

Approx. Rs 5,321 / PieceGet Latest Price

• Roller chain sprocket hobs
• Worm wheel hobs
• Spline hobs
• Chamfer hobs
• Spur and helical gear hobs
• Straight side spline hobs
• Involute spline hobs
• Serration hobs
• Semitopping gear hobs

Approx. Rs 2,521 / PieceGet Latest Price